mn101c77a, mn101c77c, MN101C77D ram ( 8-bit) rom ( 8-bit) type minimum instruction execution time standard: 0.1 s (at 2.5 v to 3.6 v, 20 mhz)* 0.2 s (at 2.1 v to 3.6 v, 10 mhz)* 0.5 s (at 1.8 v to 3.6 v, 4 mhz)* 62.5 s (at 1.8 v to 3.6 v, 32 khz)* double speed: 0.119 s (at 2.5 v to 3.6 v, 8.39 mhz)* * the operation guarantee range for flash memory built-in type is 2.7 v to 3.6 v. interrupts ? reset watchdog external 0 external 1 external 2 external 3 external 4 timer 0 timer 1 timer 4 timer 5 timer 6 time base serial 0 reception serial 0 transmission serial 1 reception serial 1 transmission serial 3 serial 4 automatic transfer finish a/d conver sion finish timer 7 (2 systems) key interrupts (8 lines) timer counter timer counter 0 : 8-bit 1 (square-wave/8-bit pwm output, event count, generation of remote control carrier, pulse width measurement) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, synchronous output event) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 4 : 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, serial 1 baud rate timer) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; 1/1 of external clock input frequency interrupt source coincidence with compare register 4 timer counter 5 : 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, serial 0 baud rate timer) clock source 1/2, 1/4 of system clock fr equency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; 1/1 of external clock input frequency interrupt source coincidence with compare register 5 package lqfp064-p-1414 *lead-free 64 k 6 k MN101C77D (under development) mad00038gem mn101c77a 32 k 1.5 k mn101c77c 48 k 3 k lqfp064-p-1414 *lead-free tqfp064-p-1010c *lead-free lqfp064-p-1414 *lead-free
mn101c77a, mn101c77c, MN101C77D timer counter (continue) timer counter 6 : 8-bit freerun timer clock source 1/1 of system clock frequency; 1/1, 1/4096, 1/8192 of osc oscillation clock frequency; 1/1, 1/4096, 1/8192 of xi oscillation clock frequency interrupt source coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave/16-bit pwm output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width measurement, input capture) clock source 1/1, 1/2, 1/4, 1/16 of system clock fr equency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 7 (2 lines) time base timer (one-minute count setting) clock source 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency watchdog timer interrupt source 1/65536, 1/262144, 1/1048576 of system clock frequency serial interface serial 0 : synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 5; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 1 : synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 4; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 3 : synchronous type/single-master i 2 c 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency serial 4 : i 2 c slave 1 applicable for i 2 c high-speed transfer mode, 7 bit/10bit address setting, general call special ports buzzer output, remote control carrier signal output, high-current drive port d/a outputs i/o pins 53 common use specified pull-up resistor available input/output selectable (bit unit) i/o see the next page for electrical characteristics, pin assignment and support tool. mad00038gem 8-bit 2-ch. (serves as ad pin, as well) 10-bit 7-ch. (with s/h) a/d inputs rom correction correcting address designation : up to 3 addresses possible max. transfer cycles : 255 starting factor : external request, various types of interrupt, software transfer mode : 1-byte transfer, word transfer, burst transfer dma controller (automatic data transfer)
pin assignment lqfp064-p-1414 * lead-free tqfp064-p-1010c * lead-free [mn101c77c] nc serves as the vpp pin in the mn101cf77g, and cannot be used as a user pin. mn101c77a mn101c77c MN101C77D electrical characteristics supply current limit symbol condition min typ max unit parameter idd1 f osc = 20 mhz, vdd = 3.3 v, (fs = fosc/2) 6 12 ma idd2 f osc = 8.39 mhz, vdd = 3.3 v, (fs = fosc/2) 3 6 ma idd3 fx = 32.768 khz, vdd = 3.3 v, (fs = fx/2) 40 a idd4 fx = 32.768 khz, vdd = 3.3 v, ta = 25 c510 a idd5 fx = 32.768 khz, vdd = 3.3 v 40 a idd6 vdd = 3.3 v, ta = 25 c02 a idd7 vdd = 3.3 v, ta = 85 c30 a operating supply current supply current at halt supply current at stop ta = ? 40 c to +85 c, vdd = 1.8 v to 3.6 v, vss = 0 v 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 an3/pa3 an4/pa4 an5/pa5 an6/pa6 nc (vpp) avdd vdd osc2 osc1 vss xi xo mmod nrst/p27 txd1a/sb01a/p00 sda4a/rxd1a/sbi1a/p01 sbi3/p50 irq4/p24 irq3/p23 irq2/p22 acz/irq1/p21 irq0/p20 tci07/p14 tci04b/p13 tc04a/p12 tci00b/p11 rmout/tc00a/p10 buzzer/p06 sbt0a/p05 rxd0a/sbi0a/p04 txd0a/sb00a/p03 scl4a/sbt1a/p02 p73/sb00b/txd0b p72/sbt1b p71/sbi1b/rxd1b p70/sb01b/txd1b p67/sd07/key7 p66/sd06/key6 p65/sd05/key5 p64/sd04/key4 p63/sd03/key3 p62/sd02/key2 p61/sd01/key1 p60/sd00/key0 p54/scl4b p53/sda4b p52/sbt3/scl3 p51/sb03/sda3 p74/sbi0b/rxd0b p75/sbt0b p76/tci01 p77/tci05 p87/led7 p86/led6 p85/led5 p84/led4 p83/led3 p82/led2 p81/led1 p80/led0 avss pa0/an0/da0 pa1/an1/da1 pa2/an2 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 mad00038gem
support tool in-circuit emulator px-ice101c/d;px-prb101c77-tqfp064-p1010c px-ice101c/d;px-prb101c77-lqfp064-p1414 flash memory built-in type mn101c77a, mn101c77c, MN101C77D mad00038gem type mn101cf77g rom ( 8-bit) 128 k ram ( 8-bit) 6 k minimum instruction ex ecution time standard: 0.1 s (at 2.7 v to 3.6 v, 20 mhz) package lqfp064-p-1414 *lead-free tqfp064-p-1010c *lead-free
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general elec- tronic equipment (such as office equipment, communications equipment, measuring instruments and house- hold appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus- tion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifica- tions satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rat- ing, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
